-
$39.95 – $59.95Price range: $39.95 through $59.95
Custom 3D printed electric toothbrush holder with slots for 4 Oral B chargers. Organize and hide your charger cords and free up valuable space. Declutter your bathroom counter while still charging your toothbrushes. This toothbrush holder is mounted by replacing your existing outlet plate with a custom design and printed plate that is provided with your purchase. This innovation looks sleek, clean and modern!
Color: White
Product Dimensions: 6.5″ x 4″ x 8.75″
Base: Oral B electric toothbrush quad slot charging base holder with custom wall plate. (Chargers and toothbrushes are not included) To ensure fit, please confirm that you have the correct Oral B charger base. (see picture)
Easy to install:
1. Remove existing wall plate and set aside the screws.
2. Attach new wall plate to toothbrush holder by sliding it into the slots on the bottom of the base. Attach wall plate with the base attached to the wall using existing screws.
3. Slide top off of base.
4. Feed the plug and desired amount of cord slack through the base hole.
5. Wind remaining cord around itself in a spiral and secure the cord tightly in the middle with a twist tie or rubber band. (see picture) Make your beginning winding loop about 3 inches
long and it should fit in the holder well with plenty of head room to slide on the top so it sits flush.
6. Repeat with 2nd,3rd and 4th charger cords if it pertains. Lay cords as flat and neat as possible.
7. Replace top by sliding it back into place to hide excess cord. Place toothbrush chargers (not included) in the cutouts. Adjust cords as needed for the charger to sit flat.
Plate style:
1. 2 Gang NEMA
2. 2 Gang GFCI
3. W-1 Gang NEMA
4. W-1 Gang GFCI
5. *CUSTOM PLATE* If you do not see what you need for your outlet wall plate please message me before ordering with a picture of your current outlet wall plate. I should be able to
design something that works. (Please note that turnaround on custom wall plates will take 3-5 extra business day due to custom plates not being stocked)
-
$19.95 – $39.95Price range: $19.95 through $39.95
Custom 3D printed electric toothbrush holder for a single Oral B charger. Organize and hide your charger cord and free up valuable space. Declutter your bathroom counter while still charging your toothbrush. This toothbrush holder is mounted by replacing your existing outlet plate with a custom design and printed plate that is provided with your purchase. This innovation looks sleek, clean and modern!
Color: White
Product Dimensions: 3.25″ x 4″ x 6.25″
Base: Oral B electric toothbrush single slot charging base holder with narrow wall plate. (Charger and toothbrush are not included) To ensure fit, please confirm that you have the correct Oral B charger base. (see picture)
Easy to install:
1. Remove existing wall plate and set aside the screws.
2. Attach new wall plate to toothbrush holder by sliding it into the slots on the bottom of the base. Attach wall plate with the base attached to the wall using existing screws.
3. Slide top off of base.
4. Feed the plug and desired amount of cord slack through the base hole.
5. Wind remaining cord around itself in a spiral and secure the cord tightly in the middle with a twist tie or rubber band. (see picture) Make your beginning winding loop about 3 inches
long and it should fit in the holder well with plenty of head room to slide on the top so it sits flush.
6. Replace top by sliding it back into place to hide excess cord. Place toothbrush charger (not included) in the cutout. Adjust cord as needed for the charger to sit flat.
Plate style:
1. 1 Gang NEMA
2. 1 Gang GFCI
3. Wall Mount Plate: This plate helps to support the holder and can be installed using wall screws (provided). The screw holes are on the inside of the toothbrush holder to hide both
the screws and the charger cord. This allows for installation near an outlet but not directly over the outlet.
4. Custom Plate: If you do not see what you need for your outlet wall plate please message me before ordering with a picture of your current outlet wall plate. I should be able to
design something that works. (Please note that turnaround on custom wall plates will take 3-5 extra business day due to custom plates not being stocked)
-
$19.95 – $39.95Price range: $19.95 through $39.95
Custom 3D printed electric toothbrush holder for a single Oral B charger. Organize and hide your charger cord and free up valuable space. Declutter your bathroom counter while still charging your toothbrush. This toothbrush holder is mounted by replacing your existing outlet plate with a custom design and printed plate that is provided with your purchase. This innovation looks sleek, clean and modern!
Color: White
Product Dimensions: 6.25″ x 4″ x 5.25″
Base: Oral B electric toothbrush single slot charging base holder with wide wall plate. (Charger and toothbrush are not included) To ensure fit, please confirm that you have the correct Oral B charger base. (see picture)
Easy to install:
1. Remove existing wall plate and set aside the screws.
2. Attach new wall plate to toothbrush holder by sliding it into the slots on the bottom of the base. Attach wall plate with the base attached to the wall using existing screws.
3. Slide top off of base.
4. Feed the plug and desired amount of cord slack through the base hole.
5. Wind remaining cord around itself in a spiral and secure the cord tightly in the middle with a twist tie or rubber band. (see picture) Make your beginning winding loop about 3 inches
long and it should fit in the holder well with plenty of head room to slide on the top so it sits flush.
6. Replace top by sliding it back into place to hide excess cord. Place toothbrush charger (not included) in the cutout. Adjust cord as needed for the charger to sit flat.
Plate style:
1. 2 Gang NEMA
2. 2 Gang GFCI
3. Wall Mount Plate: This plate helps to support the holder and can be installed using wall screws (provided). The screw holes are on the inside of the toothbrush holder to hide both
the screws and the charger cord. This allows for installation near an outlet but not directly over the outlet.
4. Custom Plate: If you do not see what you need for your outlet wall plate please message me before ordering with a picture of your current outlet wall plate. I should be able to
design something that works. (Please note that turnaround on custom wall plates will take 3-5 extra business day due to custom plates not being stocked)
-
$29.95 – $49.95Price range: $29.95 through $49.95
Custom 3D printed electric toothbrush holder with slots for 2 Oral B chargers. Organize and hide your charger cords and free up valuable space. Declutter your bathroom counter while still charging your toothbrushes. This toothbrush holder is mounted by replacing your existing outlet plate with a custom design and printed plate that is provided with your purchase. This innovation looks sleek, clean and modern!
Color: White
Product Dimensions: 6.5″ x 4″ x 5.25″
Base: Oral B electric toothbrush double slot charging base holder with custom wall plate. (Chargers and toothbrushes are not included) To ensure fit, please confirm that you have the correct Oral B charger base. (see picture)
Easy to install:
1. Remove existing wall plate and set aside the screws.
2. Attach new wall plate to toothbrush holder by sliding it into the slots on the bottom of the base. Attach wall plate with the base attached to the wall using existing screws.
3. Slide top off of base.
4. Feed the plug and desired amount of cord slack through the base hole.
5. Wind remaining cord around itself in a spiral and secure the cord tightly in the middle with a twist tie or rubber band. (see picture) Make your beginning winding loop about 3 inches
long and it should fit in the holder well with plenty of head room to slide on the top so it sits flush.
6. Repeat with 2nd,3rd and 4th charger cords if it pertains. Lay cords as flat and neat as possible.
7. Replace top by sliding it back into place to hide excess cord. Place toothbrush chargers (not included) in the cutouts. Adjust cords as needed for the charger to sit flat.
Plate style:
1. 2 Gang NEMA
2. 2 Gang GFCI
3. 1 Gang NEMA
4. 1 Gang GFCI
5. Wall Mount Plate: This plate helps to support the holder and can be installed using wall screws (provided). The screw holes are on the inside of the toothbrush holder to hide both
the screws and the charger cord. This allows for installation near an outlet but not directly over the outlet.
6. Custom Plate: If you do not see what you need for your outlet wall plate please message me before ordering with a picture of your current outlet wall plate. I should be able to
design something that works. (Please note that turnaround on custom wall plates will take 3-5 extra business day due to custom plates not being stocked)
-
$34.95 – $54.95Price range: $34.95 through $54.95
Custom 3D printed electric toothbrush holder with slots for 3 Oral B chargers. Organize and hide your charger cords and free up valuable space. Declutter your bathroom counter while still charging your toothbrushes. This toothbrush holder is mounted by replacing your existing outlet plate with a custom design and printed plate that is provided with your purchase. This innovation looks sleek, clean and modern!
Color: White
Product Dimensions: 6.5″ x 4″ x 8.75″
Base: Oral B electric toothbrush triple slot charging base holder with custom wall plate. (Chargers and toothbrushes are not included) To ensure fit, please confirm that you have the correct Oral B charger base. (see picture)
Easy to install:
1. Remove existing wall plate and set aside the screws.
2. Attach new wall plate to toothbrush holder by sliding it into the slots on the bottom of the base. Attach wall plate with the base attached to the wall using existing screws.
3. Slide top off of base.
4. Feed the plug and desired amount of cord slack through the base hole.
5. Wind remaining cord around itself in a spiral and secure the cord tightly in the middle with a twist tie or rubber band. (see picture) Make your beginning winding loop about 3 inches
long and it should fit in the holder well with plenty of head room to slide on the top so it sits flush.
6. Repeat with 2nd,3rd and 4th charger cords if it pertains. Lay cords as flat and neat as possible.
7. Replace top by sliding it back into place to hide excess cord. Place toothbrush chargers (not included) in the cutouts. Adjust cords as needed for the charger to sit flat.
Plate style:
1. 2 Gang NEMA
2. 2 Gang GFCI
3. W-1 Gang NEMA
4. W-1 Gang GFCI
5. *CUSTOM PLATE* If you do not see what you need for your outlet wall plate please message me before ordering with a picture of your current outlet wall plate. I should be able to
design something that works. (Please note that turnaround on custom wall plates will take 3-5 extra business day due to custom plates not being stocked)
